|
PROGRAM
MODES
The IDS 410 is preprogrammed with 10 different modes of operation to
accommodate most of the basic industrial scale applications.
The mode is selected and easily configured from the keyboard during
initial setup. The unit will operate in the mode selected until the user
reconfigures it.
MODE
0: Push-button tare.
Used for basic gross or net mode weighing.
MODE
1 : Keyboard tare.
Allows the user to keyboard enter a tare weight which can be used for net
weight calculation.
MODE
2 : Accumulate with
Running Total.
Accumulate gross or net weights and maintain running total for job,
lot, etc. Calculates G,T,N, totals.
MODE
3 : Print Weight With Subtotal and Total.
You can print the lot or job or lot subtotal whenever needed.
Totalized and clear at the end of the run.
MODE
4 : Manual (Axle) Weigh.
Push the PRINT button to sequentially number and print a series of
weighments. Push the TOTAL button to print and clear the total and reset
the sequence number.
MODE
5 : Automatic (Axle) weigh.
This mode operates similar to Mode 4 except printing is automatic when
motion settles. Traffic light control, trip level selection, and delay
times for control functions are provided.
MODE
6 : Automatic Axle weight On Long Scales.
Weigh by axle on a
truck scale. weight on the scale is automatically tared off after each
weihgment.Operation, controls and selections are the same as Mode 5.
MODE
7 : Peak Hold Mode.
Display and print
the peak weight detected by the indicator in the gross or net mode.
MODE
8 : Over / Under Checkweigh.
Provides three TTL outputs and two setpoints. Outputs can be used
with lights or alarms to indicate weight on the scale is over, under, or
between setpoint weights.
MODE
9 : Bulkweigh.
Features a
setpoint with remote start / stop option and fill control relay signal.
Scale empty weight and draft weights are configurable. Use for multiple
drafts with total and subtotal printing.
COMMUNICATIONS
Serial
Port 1: .................................
RS232 or 20ma current loop.
Serial Port 2:
................................. RS232 or RS485.
Digital Port:
................................. 3 TTL inputs and
3 TTL outputs.
OPTIONS
Input
power option:
12 to 28 VDC.
Analog
Output:
Provides 4-20ma, 0-20ma, 0-24ma, 0-5v, 0-10v outputs with 16-bit
resolution for process control.
Relay
Module:
The relay module accommodates 3 optically-isolated input and or output,
solid-state relays.
Time
and Date module:
Y2K compliant clock.
SPECIFICATIONS
GENERAL
SPEC.
Power: 120
VAC ±10%, 50/60 Hz or 10 to 28 VDC optional. Power supply is
mounted internally. Ligtning protection for load cell and AC input
lines is standard.
Power
Consumption operating:
13 watts @ 115VAC, 20 watts @ 12VDC.
Operating
Temperature:
-10 to +40 oC.
Size:
11" wide, 8" high, and 2" deep (28 x 20 x 5 cm).
Weight:
6 lbs (2.72 kg).
SCALE
SPEC.
Display: ................................
1-inch x 6-digit numeric, 5-LED status
indicators.
Keyboard: ..........................
Sealed with tactile feel.
Display Graduations: .........
200,000 industrial; 10,000 HB44.
Display increments: ........
1, 2, 5, 10, 20, 50.
Decimal Point: ..................
0 to 4 decimal places.
Internal Graduations: ........
1,024,000.
Conversation Rate: ........
60/sec. @ 60 HZ line frequency.
Signal Sensitivity: ...........
0.1 uV/grad (min).
Signal Range: ...................
0.5 mv/V to 6mv/V
Load Cell Excitation: .......
10 V
Load Cell Current: .........
240 ma with eight 350 ohm load cells.
Auto Zero Tracking: ......
0-60 grads @ 1/4 grad increments.
Auto Zero Delay: ............
0-25 sec. @ 0.1 sec. increments.
Linerization: .......................
5 point.
Digital Filter:
.................... Using
advanced DSP algorithm.
Digital Calibration: .......
Features front panel calibratin. Zero
and Span stored in EAROM.
Watchdog Timer: .........
Fault tolerant operatio
Download data sheet PDF
format (218k) |
&
Purchase Orders (with approved